Question:
How to Speed Up Windows XP (Different Kind of Problem)?
SheilaVisor
2008-07-04 21:36:24 UTC
I found my old Matrox Millennium G2 AGP video card in the basement and I decided to give it to my grandparents (yes, they know how to use computers lol). But before i gave it to them ,i tested it in my Computer just to make sure it still works. I have an integrated S3 graphics Prosavage DDR video card, 32 mb memory with a 2.66 GHz Intel Celeron Processor. So i plugged it in, updated drivers, All works properly. Turned the power off, removed the card, turned it back on.

Here is the problem: Everything went SLOW.
I defragged, Tried Disk clean up , and so on.......but it still SLOW.

I dont know the whats problem........Everything worked fine until i removed the Matrox video Card. Even the internet went slow.

HELP
Nine answers:
2xs
2008-07-05 20:37:48 UTC
.....wow....

Some super long answers here but did anyone even mention system restore? I'm not sure, 'cause there's NO way I'm sittin' here and reading through all this junk.

Try these options(forgive me if I mention the obvious, but you never know):

-Make sure that you disabled the Matrox card in Device manager.

-Roll back drivers for integrated video card

-Uninstall/reinstall integrated card in device manager

-System restore

-(long shot here)Try CHKDSK /r. Click Start, and then Run. In Open, type cmd, and then press ENTER. At the command prompt, type chkdsk /r



I truly feel your pain, and wish you luck.

P.S.- I'm going to include a link to TGTC(PDF format). It is the most complete Windows A-Z that you can get(for free). You need Adobe Acrobat 8.0 or higher to open it. Don't miss out on this guide.☺☻
anonymous
2008-07-04 21:41:44 UTC
When you updated the drivers did you possibly download a virus at the same time?



Try updating the drivers for the integrated card and see if that fixes the issue, it could just be that it's having a bad attitude because it thought you were replacing it, once it realizes it's still the top dog then it might calm down ;-)



Hope this helps.



By the way, my granny uses the computer regularly and she's 86 ... some old folks totally rock eh?
Duke
2008-07-04 21:48:59 UTC
Seem like your windows system has been conflicted due to 2 video drivers software boost up as the same time, go to the the control panel, click the performance & maintenance, then click the system, then click hardware tab, then click device manager and remove the drive of AGP video card that you were installed earlier.

Good luck.
DavidNH
2008-07-04 21:41:57 UTC
Some anti-virus software can slow your computer to a crawl, particularly if you have two or more programs competing at the same time to be the head honcho virus detector. Delete them and use only one.
anonymous
2016-04-08 11:06:03 UTC
it may be a virus or your background file corrupt or corrupt explorer.exe just scan your pc with anti virus. another is stop your start up process.
falconsport
2008-07-04 21:41:54 UTC
seems like you have driver conflict. the fastes way to solve it is reinstal your windows...
Crushed Ice
2008-07-04 21:59:42 UTC
google: tuneup utilities



look for ME compatible utilities
Juan F
2008-07-04 21:53:38 UTC
It has happend to all of us at least once, and some of us have try the normal process to speed up our machines, but when in doubt, what I did was:



1.- Made a back up of all my important files

2.- Try to reset the whole thing (u no) everything ---but it din't work, lol--- so,

3,- I took it to my nearest Staples Store === www.staples.com === where they have this cupon for free tune up, and WAM.

--------Back to bussiness AGAIN-------



I know, it might not be the answer you where looking for but it worked for me, and for FREE.

So give it a try, by the way the cupons usually are by the cashier, don't look for them on line or on the sunday's paper --you won't find it--



Other more tedious way is this:



Tweaking Windows XP Web





Exclusive from: Joel Durham Jr. – ExtremeTech Wed Feb 2, 5:38 PM ET





Don't you love the feeling of unbridled speed when you start using a new computer, or you drop a fresh, clean installation of Windows onto your PC's hard drive? Wow, you marvel, I didn't know a computer could run this smoothly! It responds so quickly! It boots up in seconds! It's the computer of my dreams!

Perhaps you're not quite that passionate, but the fact is, a freshly installed Windows XP (news - web sites) tends to run a lot better than one you've been using heavily for the past year or two. That's because as you install programs, as they add little background applets that start when the system boots, as you download more and more files, and, in general, as you use the computer, the sheer amount of stuff that Windows has to do increases.

More files in your folders means Windows has more to sift through when searching for something. Applets running in the background eat up memory and resources. Adding and deleting files and programs causes the data on the hard drive to fragment, making Windows work harder to read them.

All is not lost. Windows XP knows the value of efficient performance, so it does some of its own housekeeping to keep itself speedy. It watches which programs you use the most and which files you access frequently, and keeps track of them in an .INI file. It keeps frequently accessed data in a cache, which it reads when you launch an application or when Windows boots up. This process is called prefetching and it's pretty cool--but there's still plenty to do to get an old Windows XP installation running like new.

Regular Maintenance

The first thing to think about is stepping up your regimen of Windows XP maintenance tasks. Windows, and the computer world at large, change all the time. Software and hardware updates come rolling in as regularly a commuter train. Windows fills up its temp directory and doesn't always clean it out. Shady Web sites try regularly to deposit programs and cookies that pry into your personal computing habits. Viruses are as common as dust. Keep on top of this stuff by doing the following:

Keep Windows up to date. Use Automatic Updates, or run Windows Update (Start/All Programs/Windows Update), at least once each week. Download all of the critical updates and any service packs that surface in the future.

Keep your system's drivers up to date. Download the latest drivers for your motherboard chip set, your graphics card, your sound card, your network interface device, your modem and anything else you can think of. Head over to the manufacturer's Web site, look for a drivers or downloads link, and be sure to get the proper drivers for your model.

Clean House. Every so often, fire up the Add/Remove Programs applet through Control Panel. Surf through the entries, looking for programs that you never use anymore. When you find one, purge your system of it. After uninstalling it, make sure its folder was deleted from the directory tree.

Stay safe. Run anti-spyware tools and anti-virus software, and use a firewall, whether it's Windows Firewall (which comes with Service Pack 2) or another firewall product. For the low down, see PC Mag's Firewalls: Software. PC Mag recommends ZoneAlarm Pro 5.5, which offers top-notch protection against a host of nasty intruders attempting to enter your PC.

Keep the hard drive tidy. Run Disk Cleanup (Start/All Programs/Accessories/System Tools/Disk Cleanup) and Disk Defragmenter (same location) at least once each month. Defragging a large drive can take a few hours, so you might start the process at the end of your day and let the computer defrag itself while you sleep.

Reduce the Overhead You can get rid of all kinds of programs that run in the background that you may not need. The easiest way to do this is with the System Configuration Utility, otherwise known as Msconfig. Launch it by clicking the Start button and then Run, typing MSCONFIG into the text box, and hitting Enter.

Click on the Startup tab and look at the contents. This is a list of things that start when the computer boots up. All of these little goodies run in the background, eating up memory and resources and slowing your system down. Smite them here.

Uncheck everything in the list, reboot and see if any of your programs or hardware devices lose functionality. If they do, run the System Configuration Utility again and recheck entries that you suspect to be the programs your system needs, rebooting between each attempt until you narrow it down. Leave everything that doesn't affect normal use of your system unchecked. This will speed the Windows boot process and clear up system resources.

Tame the Paging File

When Windows doesn't find enough physical memory in your computer to do something it needs to do, it swaps contents of the memory out to "virtual memory" on the hard drive. The virtual memory is located in a file called a paging file.

By default, the paging file resides on your system's C: drive, and its size is dynamic, changing when Windows decides it has to grow or shrink. This leads to performance problems: not only does Windows thrash the hard drive and slow everything down while it's adjusting the paging file size, but if the paging file becomes fragmented it can be a performance nightmare.

Ideally, the paging file should reside on a secondary physical hard drive in its own partition. That's not always practical, however, so I suggest you force Windows to use a static paging file and defrag the paging file every month or so. Here's how to set up a static paging file:

1. Right-click My Computer

2. Click Properties

3. Click the Advanced tab.

4. Under the Performance heading, click Settings

5. Click the Advanced tab.

6. Under the Virtual Memory heading, click Change.

You're going to set the virtual memory to a custom size by making the initial size the same as the maximum size. How big should it be? There are all kinds of complicated formulas all over the 'Net trying to answer this question. I don't have one. I simply look, at bottom of the Virtual Memory dialog you've just opened, at the "Recommended" size, and roughly double it. For instance, if I encounter a recommended paging file size of 1574 MB, I'll make the static paging file 3000 MB even.

Simply enter your ideal paging file size in the Initial Size and Maximum Size boxes, and click OK until you get back to the desktop. You'll probably have to reboot for the new setting to take effect.

You should also defrag the paging file every few weeks. Contrary to popular belief, you don't need a third-party disk manager to defrag the paging file. To do it with Windows XP's Disk Defragmenter, simply do this:

1. Open the Virtual Memory dialog following the steps above.

2. Click on the No paging file radio button.

3. Click OK until you get back to the desktop.

4. Reboot.

5. Run Disk Defragmenter. Defrag the drive on which the paging file resides, whether Disk Defragmenter thinks it needs it or not.

6. Reboot.

7. Open the Virtual Memory dialog and set the Initial and Maximum paging file sizes to the same value (double the "recommended" size).

8. Click OK back to the desktop.

9. Reboot.

For even more tips and techniques for optimizing Windows XP, check out my article at ExtremeTech.com.

Joel Durham Jr. is the author of PC Modding For Dummies (2005, Wiley) and has been a writer in the computer and PC gaming industries since 1996



As you can tell it has been with me for a while but it has help me on tight moments



BEST OF LUCK!



Juan Flores

www.Winnerpeople.com
¥♥gi
2008-07-04 22:01:19 UTC
Optimize Windows Vista for better performance

Applies to all editions of Windows Vista.

Which edition of Windows Vista am I using?

In this articleDelete programs you never use

Limit how many programs load at startup

Defragment your hard drive

Clean up your hard disk

Run fewer programs at the same time

Turn off visual effects

Try restarting if there's a problem

Add more memory

Check for viruses and spyware

Check your computer’s speed

Disable services you don’t need

Check for updates from the manufacturer

Don’t settle for slow

No matter how fast or shiny computers might be when they are new, they all seem to get slower over time. That state-of-the-art PC you bought last year might not feel like such a screamer after you install a dozen programs, load it with antispyware and antivirus tools, and download untold amounts of junk from the Internet. The slowdown might happen so gradually you hardly notice it, until one day you’re trying to open a program or file and wonder, "What happened to my poor PC?"



Whatever the cause, there are a lot of ways to help speed up Windows and make your PC work better—even without upgrading your hardware. Here are some tips to help you optimize Windows Vista for faster performance.



Delete programs you never use

Many PC manufacturers pack their new computers with programs you didn’t order and might not want. These often include trial editions and limited edition versions of programs that software companies hope you will try, find useful, and then pay to upgrade to full versions or newer versions. If you decide you don’t want them, keeping the software on your computer might slow it down by using precious memory, disk space, and processing power.



It’s a good idea to uninstall all the programs you don’t plan to use. This should include both manufacturer-installed software and software you installed yourself but don’t want anymore—especially utility programs designed to help manage and tune your computer’s hardware and software. Utility programs such as virus scanners, disk cleaners, and backup tools often run automatically at startup, quietly chugging along in the background where you can’t see them. Many people have no idea they are even running.



Even if your PC is older, it might contain manufacturer-installed programs that you never noticed or have since forgotten about. It’s never too late to remove these and get rid of the clutter and wasted system resources. Maybe you thought you might use the software someday, but never did. Uninstall it and see if your PC runs faster.



For instructions, see Uninstall or change a program.



Top of page

Limit how many programs load at startup

Many programs are designed to load automatically when Windows starts. Software manufacturers often set their programs to open in the background, where you can’t see them running, so they’ll open right away when you click their icons. That's helpful for programs you use a lot, but for programs you rarely or never use, this wastes precious memory and slows down the time it takes Windows to finish loading.



Decide for yourself if you want a program to load at startup.



But how can you tell what programs load automatically at startup? Sometimes this is obvious, because the program will add an icon to the notification area on the taskbar, where you can see it running. Look there and see if there are any programs running that you don’t want to load automatically. Position your mouse over each icon to see the program name. Be sure to click the Show hidden icons button so you don’t miss any icons.





The Show hidden icons button in the notification area





Even after you check the notification area, you might still have missed some programs that load automatically at startup. You can find and disable them using Windows Defender.





The Software Explorer screen in Windows Defender shows which programs automatically start when you launch Windows





If you’re unsure about whether a program should open automatically at startup, you can try disabling it, restarting your computer, and then using the program. If that causes any problems with the program, you can go back and re-enable it to start automatically.



For instructions how to use Windows Defender to check for programs that open automatically, see Stop a program from running automatically when Windows starts.



NoteSome people prefer to manage which programs load at startup using the System Configuration tool. For more information, see Start System Configuration.



Top of page

Defragment your hard drive

Fragmentation makes your hard disk do extra work that can slow down your computer. Disk Defragmenter rearranges fragmented data so your hard disk can work more efficiently. Disk Defragmenter runs on a schedule, but you can also defragment your hard disk manually.



For more information, see Improve performance by defragmenting your hard disk.



Top of page

Clean up your hard disk

If you want to reduce the number of unnecessary files on your hard disk to free up disk space and help your computer run faster, use Disk Cleanup. It removes temporary files, empties the Recycle Bin, and removes a variety of system files and other items that you no longer need. For step-by-step instructions on how to do this, see Delete files using Disk Cleanup.



Top of page

Run fewer programs at the same time

Sometimes changing your computing behavior can have a big impact on your PC's performance. If you’re the type of computer user who likes to keep eight programs and a dozen browser windows open at once—all while instant messaging your friends—don’t be surprised if your PC bogs down. Keeping a lot of e‑mail messages open can also use up memory.



If you find your PC slowing down, ask yourself if you really need to keep all your programs and windows open at once. Find a better way to remind yourself to reply to e‑mail messages than to keep all of them open.



Top of page

Turn off visual effects

If Windows is running slowly, you can speed it up by disabling some of its visual effects. It comes down to appearance versus performance. Would you rather have Windows run faster or look prettier? If your PC is fast enough, you don’t have to make this tradeoff, but if your computer is just barely powerful enough for Windows Vista, it can be useful to scale back on the visual bells and whistles.



You can choose which visual effects to turn off, one by one, or you can let Windows choose a bunch for you. There are 20 visual effects you can control, such as the transparent glass look, the way menus open or close, and whether shadows are displayed.





The Performance Options dialog box lets you turn on or off up to 20 visual effects





To adjust all visual effects for best performance:





1. Open Performance Information and Tools by clicking the Start button , clicking Control Panel, clicking System and Maintenance, and then clicking Performance Information and Tools.



2. Click Adjust visual effects. If you are prompted for an administrator password or confirmation, type the password or provide confirmation.



3. Click the Visual Effects tab, click Adjust for best performance, and then click OK. (For a less drastic option, select Let Windows choose what’s best for my computer.)







Top of page

Try restarting if there's a problem

This tip is simple. If your computer seems to be running slowly and closing all the currently running programs doesn't help, trying restarting your computer. Restarting can fix performance problems where the exact cause is hard to pinpoint.



Top of page

Add more memory

This isn’t a guide to buying hardware that will speed up your computer. But no discussion of how make Windows run faster would be complete without mentioning that you should consider adding more memory to your PC.



If a computer running Windows Vista feels too slow, it’s usually because the PC doesn’t have enough memory. The most sure–fire way to speed it up is to add more.



Windows Vista can run on a PC with 512 megabytes (MB) of random access memory (RAM), but it runs better with 1 gigabyte (GB). For optimal performance, boost that to 2 GB or more.



If you're going to the trouble of opening up your PC case to add more memory, you might as well boost the total to at least 2 GB. Especially if you're the sort of person who keeps a dozen e‑mail messages, ten browser windows, and six other programs open at once—all while instant messaging.



Another option is to boost the amount of memory by using Windows ReadyBoost. This feature allows you to use the storage space on some removable media devices, such as USB flash drives, to speed up your computer. It’s easier to plug a flash drive into a USB port than to open your PC case and plug memory modules into its motherboard. For more information, see Using memory in your storage device to speed up your computer.



Top of page

Check for viruses and spyware

If your PC is running slowly, one dreaded possibility is that it might be infected with a virus or spyware. This is not as common as the other problems, but it is something to consider. Before you worry too much, check your PC using antispyware and antivirus programs.



A common symptom of a virus is a much slower-than-normal computer performance. Other signs include unexpected messages that pop up on your PC, programs that start automatically, or the sound of your hard disk constantly working.



Spyware is a type of program that is installed, usually without your knowledge, to watch your activity on the Internet. You can check for spyware with Windows Defender or other anti-spyware programs. For more information, see How to tell if your computer is infected with spyware.



The best way to deal with viruses is to prevent them in the first place. Always run antivirus software and keep it up to date


This content was originally posted on Y! Answers, a Q&A website that shut down in 2021.
Loading...